fc www.vishay.com vishay dale thin film revision: 26-jun-12 1 document number: 60093 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 high frequency (up to 20 ghz) resistor, thin film surface mount chip fc series chip resistors ar e designed with low internal reactance. they function as almost pure resistors on a very high range of frequencies. the specialized laser edge trimming allows for precision tolerances to 0.1 %. features ? small standard size 0402 case size ? edge trimmed block resistors ? alumina substrate high purity (99.6 %) ? ohmic range (10 ? to 1000 ? ) ? small internal reactance (< 10 m ? ) ? low tcr (down to 25 ppm/c) ? epoxy bondable termination available ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 note * lead (pb)-containing terminations are not rohs-compliant. exemptions may apply. applications ? low noise amplifiers ? attenuation ? line termination standard electrical specifications test specifications conditions material passivated nichrome - resistance range 10 ? to 1000 ? case size dependent tcr: absolute 25 ppm/c (standard) ( ? 50 ? ) to 100 ppm/c - 55 c to + 125 c tolerance: absolute 0.1 % to 5.0 % + 25 c stability: absolute ? r 0.02 % 2000 h at 70 c stability: ratio -- voltage coefficient 0.1 ppm/v - working voltage 30 v to 75 v - operating temperature range - 55 c to + 125 c - storage temperature range - 55 c to + 150 c - noise < - 35 db - shelf life stability: absolute ? r 0.01 % 1 year at + 25 c component ratings case size power rating (mw) working voltage (v) resistance range ( ? ) 0402 50 30 10 to 1000 0505 125 37 20 to 1000 0603 125 50 10 to 1000 0805 200 50 10 to 1000 1005 250 75 10 to 1000 1206 330 75 10 to 1000
fc www.vishay.com vishay dale thin film revision: 26-jun-12 2 document number: 60093 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note (1) preferred packaging code dimensions in inches (millimeters) case size length width w ( 0.005) thickness typical top pad d ( 0.005) bottom pad e ( 0.005) 0402 0.042 0.008 (1.067 0.203) 0.022 (0.559) 0.015 (0.381) 0.010 (0.254) 0.010 (0.254) 0505 0.055 0.006 (1.397 0.152) 0.050 (1.270) 0.015 (0.381) 0.010 (0.254) 0.015 (0.381) 0603 0.064 0.006 (1.626 0.152) 0.032 (0.813) 0.015 (0.381) 0.012 (0.305) 0.015 (0.381) 0805 0.080 0.006 (2.032 0.152) 0.050 (1.270) 0.015 (0.381) 0.016 0.008 (0.406 0.203) 0.015 (0.381) 1005 0.105 0.008 (2.667 0.203) 0.050 (1.270) 0.015 (0.381) 0.015 (0.381) 0.015 (0.381) 1206 0.126 0.008 (3.200 0.203) 0.063 (1.600) 0.015 (0.381) 0.020 + 0.005/- 0.010 (0.508 + 0.127/- 0.254) d l e t w l dt mechanical specifications resistive element passivated nichrome substrate material alumina terminations pre-soldered or gold lead (pb)-free option 96.5 % sn, 3.0 % ag, 0.5 % cu tin/lead option sn63 lead (pb)-free fi nish and tin/lead hot solder dip global part number information new global part nu mbering: fc1206e1001bbts global model case size tcr characteristic resistance tolerance termination (1, 2 or 3 digits) packaging fc 0402 0505 0603 0805 1005 1206 e = 25 ppm/c h = 50 ppm/c k = 100 ppm/c the first 3 digits are significant figures and the last digit specifies the number of zeros to follow. r designates the decimal point. example: 10r0 = 10 ? 1000 = 100 ? 1001 = 1 k ? b = 0.1 % d = 0.5 % f = 1 % g = 2 % j = 5 % t = top sided au (gold) term au over ni epoxy bondable rohs compliant - e4 b = wraparound sn/pb solder 63 % sn/37 % pb w/nickel barrier g = wraparound au over ni (gold) termination epoxy bondable rohs compliant - e4 tb = top sided sn/pb solder 63 % sn/37 % pb w/nickel barrier tbs = top sided lead (pb)-free solder w/nickel barrier rohs compliant - e1 s = wraparound lead (pb)-free solder 96.5 % sn/3.0 % ag/0.5 %cu rohs compliant - e1 bs = bulk 100 min., 1 mult ws = waffle 100 min., 1 mult tape and reel t0 = 100 min., 100 mult t1 = 1000 min., 1000 mult (1) t3 = 300 min., 300 mult t5 = 500 min., 500 mult tf = full reel ts = 100 min., 1 mult historical part number example: fc1206e 1001bbt (for reference purposes only) fc 1206 e 1001 b b t series case size tcr characteristic resistance tolerance termination packaging 206k 000 1 1 fc bt b st s 206e 001 1 1 fc bb t s
fc www.vishay.com vishay dale thin film revision: 26-jun-12 3 document number: 60093 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 typical high frequency performance electrical model and testing the lumped circuit above was used to model the data at the bond ing pad-resistor refe rence plane. high frequency testing was performed by modelithics, inc. on parts mounted to quartz test boards. quartz test boards were chosen to minimize the contribution of the board effects at high frequencies. future te sting will be performed on vari ous industry standard board type s. vishay in partnership with modelit hics, inc. will develop substrat e scalable models for the fc se ries resistors. these models w ill be available for industry standa rd design software packages and will allow the designer to accurately model their wireless and microwave printed boards. lumpe d e q uivalent circuit reference plane is at the resistor- b on d in g pa d interface. c: internal s hunt capacitance l : internal inductance r: re s i s tance l c : external connection inductance c g : external capacitance to ground c g c g l c r l c l c internal impedance 0402 wraparoun d 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 fre q uency ( g hz) 0402 flip chip 75 100 250 500 50 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 fre q uency ( g hz) 060 3 flip chip 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.1 1 10 fre q uency ( g hz) 0.1 1 10 0.1 1 10 c = 0.0262 pf l = 0.00189 nh c = 0.0403 pf l = 0.0267 nh c = 0.0392 pf l = 0.1209 nh |zin|/r |zin|/r |zin|/r 1000 100 250 500 50 1000 75 100 500 50 1000
fc www.vishay.com vishay dale thin film revision: 26-jun-12 4 document number: 60093 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 v s wr fc s eries 0402 size 50 2.0 fre q uency ( g hz) 1 1.0 1.9 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.1 20 19 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 218 v s wr fc s eries 0402 size 100 2.0 fre q uency ( g hz) 1 1.0 1.9 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.1 20 19 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 218
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
